Asder Опубликовано 10 Августа 2022 Поделиться Опубликовано 10 Августа 2022 Всем привет, подскажите (кто что сможет) по этому аппарату. А то, что то я в тупике. Итак : прибыло два аппарата (после имерсии) один включается, второй вообще молчит, тот что включается все три платы 0 асиков, тот что не включается лег блок ( и с ним в целом все понятно, в работе), но.... с аппарата где мертвый блок вытащил хешки и установил в аппарат который запускается, результат тот же, все платы 0 асиков. И всё бы ничего, но второе НО, на тестере (stasic tester) если сканировать в режиме S19j (поддержки именно S19j pro еще нет) считывается 88 чипов (на про 126 чипов) и корректно считываются температуры. Все сигналы (RX.TX.CLK.RST.Bi) в норме, буст работает, по LDO все стабы рабочие и все напряжения в норме. И вот такой вот ребус ))) P.S. контролька на амилоджике, последнее ПО прошил. Уж не знаю, что еще проверить.... [spoiler= clog] Цитата [ 0.000000@0] Booting Linux on physical CPU 0x0 [ 0.000000@0] Linux version 4.9.113 (jenkins@nomd-nomd-fwc-bj) (gcc version 6.3.1 20170109 (Linaro GCC 6.3-2017.02) ) #1 SMP PREEMPT Tue Oct 19 21:56:04 CST 2021 [ 0.000000@0] Boot CPU: AArch64 Processor [410fd034] [ 0.000000@0] earlycon: aml_uart0 at MMIO 0x00000000ff803000 (options '') [ 0.000000@0] bootconsole [aml_uart0] enabled [ 0.000000@0] efi: Getting EFI parameters from FDT: [ 0.000000@0] efi: UEFI not found. [ 0.000000@0] 07400000 - 07500000, 1024 KB, ramoops@0x07400000 [ 0.000000@0] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB [ 0.000000@0] 05000000 - 05400000, 4096 KB, linux,secmon [ 0.000000@0] __reserved_mem_alloc_size, start:0x000000003e000000, end:0x0000000040000000, len:32 MiB [ 0.000000@0] failed to allocate memory for node linux,meson-fb, size:32 MB [ 0.000000@0] cma: Reserved 8 MiB at 0x000000000f800000 [ 0.000000@0] On node 0 totalpages: 65536 [ 0.000000@0] DMA zone: 1024 pages used for memmap [ 0.000000@0] DMA zone: 0 pages reserved [ 0.000000@0] DMA zone: 65536 pages, LIFO batch:15 [ 0.000000@0] psci: probing for conduit method from DT. [ 0.000000@0] psci: PSCIv1.0 detected in firmware. [ 0.000000@0] psci: Using standard PSCI v0.2 function IDs [ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000@0] psci: SMC Calling Convention v1.1 [ 0.000000@0] percpu: Embedded 25 pages/cpu @ffffffc00f753000 s64536 r8192 d29672 u102400 [ 0.000000@0] pcpu-alloc: s64536 r8192 d29672 u102400 alloc=25*4096 [ 0.000000@0] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000@0] Detected VIPT I-cache on CPU0 [ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512 [ 0.000000@0] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xff803000 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=,loaded,androidboot.selinux=enforcing androidboot.firstboot=1 jtag=disable androidboot.hardware=amlogic androidboot.bootloader=U-Boot 2015.01 androidboot.build.expect.baseband=N/A androidboot.serialno=1234567890 rootfstype=ramfs init=/sbin/init [ 0.000000@0] PID hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000000@0] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000@0] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) [ 0.000000@0] Memory: 219920K/262144K available (8764K kernel code, 1194K rwdata, 2428K rodata, 3648K init, 1018K bss, 29936K reserved, 12288K cma-reserved) [ 0.000000@0] Virtual kernel memory layout: [ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB) [ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB) [ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009910000 ( 8768 KB) [ 0.000000@0] .rodata : 0xffffff8009910000 - 0xffffff8009b80000 ( 2496 KB) [ 0.000000@0] .init : 0xffffff8009b80000 - 0xffffff8009f10000 ( 3648 KB) [ 0.000000@0] .data : 0xffffff8009f10000 - 0xffffff800a03aa00 ( 1195 KB) [ 0.000000@0] .bss : 0xffffff800a03aa00 - 0xffffff800a139534 ( 1019 KB) [ 0.000000@0] fixed : 0xffffffbefe7fb000 - 0xffffffbefec00000 ( 4116 KB) [ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB) [ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum) [ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf00400000 ( 4 MB actual) [ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc010000000 ( 256 MB) [ 0.000000@0] can't find symbol:arm_dma_alloc [ 0.000000@0] can't find symbol:__alloc_from_contiguous [ 0.000000@0] can't find symbol:cma_allocator_alloc [ 0.000000@0] 0, addr:ffffff800971cff0 + 140, aml_cma_alloc_post_hook [ 0.000000@0] 1, addr:ffffff800951f258 + 78, dma_alloc_from_contiguous [ 0.000000@0] 2, addr:ffffff80091fdd50 + 388, cma_alloc [ 0.000000@0] 3, addr:ffffff80091f76c8 + 2d0, __kmalloc_track_caller [ 0.000000@0] 4, addr:ffffff80091f4a70 + 2d0, __kmalloc [ 0.000000@0] 5, addr:ffffff80091f4750 + 258, kmem_cache_alloc_trace [ 0.000000@0] 6, addr:ffffff80091f4500 + 250, kmem_cache_alloc [ 0.000000@0] 7, addr:ffffff80091f4490 + 70, __slab_alloc.isra.24.constprop.28 [ 0.000000@0] 8, addr:ffffff80091f4108 + 388, ___slab_alloc.constprop.29 [ 0.000000@0] 9, addr:ffffff80091f1e70 + 420, new_slab [ 0.000000@0] 10, addr:ffffff80091e52f8 + b0, vzalloc [ 0.000000@0] 11, addr:ffffff80091e5248 + b0, vmalloc [ 0.000000@0] 12, addr:ffffff80091e4b00 + 2e0, __vmalloc_node_range [ 0.000000@0] 13, addr:ffffff80091ca410 + 110, kmalloc_order_trace [ 0.000000@0] 14, addr:ffffff80091ca2a0 + 170, kmalloc_order [ 0.000000@0] 15, addr:ffffff80091ab5a8 + 168, __alloc_page_frag [ 0.000000@0] 16, addr:ffffff80091ab540 + 68, alloc_pages_exact [ 0.000000@0] 17, addr:ffffff80091ab510 + 30, get_zeroed_page [ 0.000000@0] 18, addr:ffffff80091ab4b8 + 58, __get_free_pages [ 0.000000@0] 19, addr:ffffff80091aa800 + cb8, __alloc_pages_nodemask [ 0.000000@0] 20, addr:ffffff800909c6e8 + 2a8, __dma_alloc [ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000@0] Preemptible hierarchical RCU implementation. [ 0.000000@0] Build-time adjustment of leaf fanout to 64. [ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=4 [ 0.000000@0] [ 0.000000@0] ********************************************************** [ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000@0] ** ** [ 0.000000@0] ** trace_printk() being used. Allocating extra memory. ** [ 0.000000@0] ** ** [ 0.000000@0] ** This means that this is a DEBUG kernel and it is ** [ 0.000000@0] ** unsafe for production use. ** [ 0.000000@0] ** ** [ 0.000000@0] ** If you see this message and you are not debugging ** [ 0.000000@0] ** the kernel, report this immediately to your vendor! ** [ 0.000000@0] ** ** [ 0.000000@0] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE ** [ 0.000000@0] ********************************************************** [ 0.000000@0] NR_IRQS:64 nr_irqs:64 0 [ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized [ 0.000000@0] axg_aoclkc_init: register ao clk ok! [ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] axg_amlogic_init_sdemmc: register amlogic sdemmc clk [ 0.000000@0] axg_amlogic_init_media: register meson media clk [ 0.000000@0] axg_amlogic_init_misc: register amlogic axg misc clks [ 0.000000@0] axg_amlogic_init_misc: register amlogic sdemmc clk [ 0.000000@0] axg_clkc_init initialization complete [ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys). [ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.008253@0] meson_bc_timer: mclk->mux_reg =ffffff800800a190,mclk->reg =ffffff800800c194 [ 0.016907@0] Console: colour dummy device 80x25 [ 0.021107@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.031586@0] pid_max: default: 32768 minimum: 301 [ 0.036442@0] thread_stack_cache_init, vmap:ffffffc00edaf600, bitmap:ffffffc00eda3000, cache page:ede0 [ 0.045772@0] thread_stack_cache_init, allocation vm area:ffffffc00edd94c0, addr:ffffff8020000000, size:20001000 [ 0.056005@0] cpu 0, vmap_stack:[ffffffc00f75c960-ffffffc00f760950] [ 0.062304@0] cpu 0, irq_stack: [ffffffc00f753060-ffffffc00f757050] [ 0.068604@0] cpu 1, vmap_stack:[ffffffc00f775960-ffffffc00f779950] [ 0.074904@0] cpu 1, irq_stack: [ffffffc00f76c060-ffffffc00f770050] [ 0.081203@0] cpu 2, vmap_stack:[ffffffc00f78e960-ffffffc00f792950] [ 0.087503@0] cpu 2, irq_stack: [ffffffc00f785060-ffffffc00f789050] [ 0.093803@0] cpu 3, vmap_stack:[ffffffc00f7a7960-ffffffc00f7ab950] [ 0.100103@0] cpu 3, irq_stack: [ffffffc00f79e060-ffffffc00f7a2050] [ 0.106465@0] Security Framework initialized [ 0.110697@0] SELinux: Initializing. [ 0.114387@0] SELinux: Starting in permissive mode [ 0.114427@0] Mount-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.121108@0] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes) [ 0.128871@0] ftrace: allocating 30089 entries in 118 pages [ 0.184480@0] sched-energy: CPU device node has no sched-energy-costs [ 0.185292@0] CPU0: update cpu_capacity 1024 [ 0.189619@0] ASID allocator initialised with 32768 entries [ 0.227595@0] secmon: can't fine clear_range [ 0.227807@0] EFI services will not be available. [ 0.231075@0] Meson chip version = RevC (25:C - 23:0) [ 0.264946@1] Detected VIPT I-cache on CPU1 [ 0.265005@1] CPU1: update cpu_capacity 1024 [ 0.265007@1] CPU1: Booted secondary processor [410fd034] [ 0.293008@2] Detected VIPT I-cache on CPU2 [ 0.293062@2] CPU2: update cpu_capacity 1024 [ 0.293064@2] CPU2: Booted secondary processor [410fd034] [ 0.321072@3] Detected VIPT I-cache on CPU3 [ 0.321125@3] CPU3: update cpu_capacity 1024 [ 0.321128@3] CPU3: Booted secondary processor [410fd034] [ 0.321220@0] Brought up 4 CPUs [ 0.360439@0] SMP: Total of 4 processors activated. [ 0.365348@0] CPU features: detected feature: 32-bit EL0 Support [ 0.371383@0] CPU features: detected feature: Kernel page table isolation (KPTI) [ 0.381951@0] CPU: All CPU(s) started at EL2 [ 0.383123@0] alternatives: patching kernel code [ 0.388453@1] addr:ffffff802007be10 is in kernel, size fix 4096->10, data:mode=0755 [ 0.395652@0] devtmpfs: initialized [ 0.411078@0] DMI not present or invalid. [ 0.411439@0] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.419457@0] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.426019@0] pinctrl core: initialized pinctrl subsystem [ 0.432443@0] NET: Registered protocol family 16 [ 0.451955@0] cpuidle: using governor menu [ 0.452442@0] vdso: 2 pages (1 code @ ffffff8009917000, 1 data @ ffffff8009f14000) [ 0.458062@0] hw-breakpoint: found 6 breakpoint and 2 watchpoint registers. [ 0.465475@0] DMA: preallocated 256 KiB pool for atomic allocations [ 0.471666@0] clkmsr: clkmsr: driver init [ 0.475674@0] aml_watch_point_probe, in, wp:2 [ 0.480265@0] pstore: using zlib compression [ 0.484605@0] console [pstore-1] enabled [ 0.487944@0] pstore: Registered ramoops as persistent store backend [ 0.494356@0] ramoops: attached 0x100000@0x7400000, ecc: 0/0 [ 0.508742@0] aml_iomap: amlogic iomap probe done [ 0.515720@0] clkmsr: msr_clk_reg0=ffffff800817e004,msr_clk_reg2=ffffff80081d100c [ 0.517647@0] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0 [ 0.614282@0] usbcore: registered new interface driver usbfs [ 0.614448@0] usbcore: registered new interface driver hub [ 0.620073@0] usbcore: registered new device driver usb [ 0.625387@0] pps_core: LinuxPPS API ver. 1 registered [ 0.630296@0] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.639697@0] PTP clock support registered [ 0.644046@0] dmi: Firmware registration failed. [ 0.652838@0] secmon: reserve_mem_size:0x300000 [ 0.653004@0] secmon secmon: assigned reserved memory node linux,secmon [ 0.660015@0] secmon: get page:ffffffbf00140000, 5000 [ 0.664664@0] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000 [ 0.673060@0] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000 [ 0.680965@0] NetLabel: Initializing [ 0.683098@0] NetLabel: domain hash size = 128 [ 0.687703@0] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.692918@0] NetLabel: unlabeled traffic allowed by default [ 0.699520@0] clocksource: Switched to clocksource arch_sys_counter [ 0.828799@0] VFS: Disk quotas dquot_6.6.0 [ 0.828945@0] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.855875@1] NET: Registered protocol family 2 [ 0.856955@1] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.862140@1] TCP bind hash table entries: 2048 (order: 3, 32768 bytes) [ 0.868795@1] TCP: Hash tables configured (established 2048 bind 2048) [ 0.875391@1] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.881346@1] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.888079@1] NET: Registered protocol family 1 [ 0.893044@1] RPC: Registered named UNIX socket transport module. [ 0.898476@1] RPC: Registered udp transport module. [ 0.903362@1] RPC: Registered tcp transport module. [ 0.908251@1] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.917495@1] Unpacking initramfs... [ 1.417786@0] Initramfs unpacking failed: junk in compressed archive [ 1.424650@0] Freeing initrd memory: 6536K [ 1.425526@0] hw perfevents: clusterb_enabled = 0 [ 1.427907@0] hw perfevents: cpumasks 0xf, 0x0 [ 1.432373@0] hw perfevents: cluster A irq = 7 [ 1.436937@0] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available [ 1.447098@0] audit: initializing netlink subsys (disabled) [ 1.450448@0] audit: type=2000 audit(1.264:1): initialized [ 1.457843@0] workingset: timestamp_bits=62 max_order=16 bucket_order=0 [ 1.482594@0] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.485673@0] NFS: Registering the id_resolver key type [ 1.488318@0] Key type id_resolver registered [ 1.492637@0] Key type id_legacy registered [ 1.497272@0] fuse init (API version 7.26) [ 1.502730@0] SELinux: Registering netfilter hooks [ 1.509014@0] NET: Registered protocol family 38 [ 1.509074@0] Key type asymmetric registered [ 1.512328@0] Asymmetric key parser 'x509' registered [ 1.517824@0] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) [ 1.525023@0] io scheduler noop registered (default) [ 1.530075@0] io scheduler deadline registered [ 1.534811@0] io scheduler cfq registered [ 1.556153@2] random: fast init done [ 1.556251@2] random: crng init done [ 1.556716@0] Unable to detect cache hierarchy for CPU 0 [ 1.588305@0] loop: module loaded [ 1.589804@0] zram: Added device: zram0 [ 1.590237@0] mtdoops: mtd device (mtddev=name/number) must be supplied [ 1.597078@0] libphy: Fixed MDIO Bus: probed [ 1.601719@0] tun: Universal TUN/TAP device driver, 1.6 [ 1.606057@0] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.614231@0] ee eth reset:Addr = ffffff80081fd008 [ 1.621768@0] meson6-dwmac ff3f0000.ethernet: no reset control found [ 1.623727@0] stmmac - user ID: 0x11, Synopsys ID: 0x37 [ 1.628958@0] Ring mode enabled [ 1.632198@0] DMA HW capability register supported [ 1.636919@0] Normal descriptors [ 1.640242@0] RX Checksum Offload Engine supported [ 1.645143@0] COE Type 2 [ 1.647766@0] TX Checksum insertion supported [ 1.652228@0] Wake-Up On Lan supported [ 1.656173@0] Enable RX Mitigation via HW Watchdog Timer [ 1.669751@0] libphy: stmmac: probed [ 1.669803@0] eth%d: PHY ID 0007c0f1 at 0 IRQ POLL (stmmac-0:00) active [ 1.676350@0] PPP generic driver version 2.4.2 [ 1.679213@0] PPP BSD Compression module registered [ 1.683752@0] PPP Deflate Compression module registered [ 1.688991@0] PPP MPPE Compression module registered [ 1.693953@0] NET: Registered protocol family 24 [ 1.699455@0] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.705358@0] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 1.712392@0] usbcore: registered new interface driver cdc_acm [ 1.717608@0] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 1.726054@0] usbcore: registered new interface driver usbserial [ 1.732787@0] mousedev: PS/2 mouse device common for all mice [ 1.738160@0] usbcore: registered new interface driver xpad [ 1.743574@0] i2c /dev entries driver [ 1.748358@0] cpu cpu0: bL_cpufreq_init: CPU 0 initialized [ 1.752564@0] arm_big_little: bL_cpufreq_register: Registered platform driver: scpi [ 1.763565@0] ff803000.serial: clock gate not found [ 1.765096@0] meson_uart ff803000.serial: ==uart0 reg addr = ffffff800830d000 [ 1.772298@0] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 13, base_baud = 1500000) is a meson_uart [ 1.787213@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200 [ 1.789914@0] console [ttyS0] enabled [ 1.797144@0] bootconsole [aml_uart0] disabled [ 1.806817@3] ff804000.serial: clock gate not found [ 1.810923@3] meson_uart ff804000.serial: ==uart3 reg addr = ffffff8008321000 [ 1.818037@3] ff804000.serial: ttyS3 at MMIO 0xff804000 (irq = 14, base_baud = 1500000) is a meson_uart [ 1.828469@2] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff8008323000 [ 1.834544@2] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 25, base_baud = 1500000) is a meson_uart [ 1.844705@0] meson_uart ffd23000.serial: ==uart2 reg addr = ffffff8008325000 [ 1.851003@0] ffd23000.serial: ttyS2 at MMIO 0xffd23000 (irq = 26, base_baud = 1500000) is a meson_uart [ 1.862004@3] amlogic-new-usb2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008348000 [ 1.871265@3] amlogic-new-usb3 ffe09080.usb3phy: This phy has no usb port [ 1.877746@3] amlogic-new-usb3 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800834c080 [ 1.892834@0] i2c i2c-1: of_i2c: modalias failure on /soc/aobus@ff800000/i2c@5000/mcu6350@40 [ 1.896588@0] i2c i2c-1: Failed to create I2C device for /soc/aobus@ff800000/i2c@5000/mcu6350@40 [ 1.909095@0] aml_dma ff63e000.aml_dma: Aml dma [ 1.912081@0] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma [ 1.917082@0] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma [ 1.923424@0] efusekeynum: 4 [ 1.925799@0] efusekeyname: mac offset: 0 size: 6 [ 1.932212@0] efusekeyname: mac_bt offset: 6 size: 6 [ 1.938611@0] efusekeyname: mac_wifi offset: 12 size: 6 [ 1.945021@0] efusekeyname: usid offset: 18 size: 16 [ 1.951882@3] efuse efuse: probe OK! [ 1.957326@3] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller [ 1.964568@3] meson-mmc: >>>>>>>>hostbase ffffff8008358000, dmode [ 1.969600@3] meson-mmc: actual_clock :400000, HHI_nand: 0x80 [ 1.974821@3] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000033c [ 2.023662@3] meson-mmc: meson_mmc_probe() : success! [ 2.023925@3] amlogic mtd driver init [ 2.028014@3] prase_get_dtb_nand_parameter:128,parse dts start [ 2.032730@3] bl mode descrete [ 2.035609@3] fip_copies 4 [ 2.038274@3] fip_size 0x200000 [ 2.041412@3] nand_clk_ctrl 0xffe07000 [ 2.045136@3] prase_get_dtb_nand_parameter:234,parse dts end [ 2.050803@3] nand_clk_ctrl 0xffe07000 [ 2.054526@3] nand register base ffffff80083df800, nand clock register ffffff80083e1000 [ 2.063270@3] plat->aml_nand_device ffffff800a005a90 [ 2.067448@3] m3_nand_probe() aml_nand_device ffffff800a005a90 [ 2.073502@3] NAND device id: 2c da 90 95 6 0 [ 2.077575@3] NAND device: Manufacturer ID: [ 2.081631@3] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A) [ 2.088673@3] oob_fill_cnt =32 oob_size =64, bch_bytes =14 [ 2.094104@3] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16 [ 2.099653@3] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1 [ 2.105898@3] mtd->oobavail: 0x8 [ 2.109397@3] aml_nand_init 2119: plat-name:bootloader [ 2.114217@3] Creating 1 MTD partitions on "bootloader": [ 2.119521@3] 0x000000000000-0x000000200000 : "bootloader" [ 2.128621@2] bootloader initialized ok [ 2.128764@2] plat->aml_nand_device ffffff800a005a90 [ 2.133760@2] m3_nand_probe() aml_nand_device ffffff800a005a90 [ 2.139872@2] NAND device id: 2c da 90 95 6 0 [ 2.143865@2] NAND device: Manufacturer ID: [ 2.147930@2] 0x2c, Chip ID: 0x2c (Micron A revision NAND 2Gib MT29F2G08-A) [ 2.154972@2] oob_fill_cnt =32 oob_size =64, bch_bytes =14 [ 2.160406@2] ecc mode:6 ecc_page_num=2 eep_need_oobsize=16 [ 2.165954@2] plane_num=1 writesize=0x800 ecc.size=0x200 bch_mode=1 [ 2.172199@2] mtd->oobavail: 0x8 [ 2.175672@2] aml_nand_init 2119: plat-name:nandnormal [ 2.180568@2] bbt_start=20 [ 2.183179@2] env_start=24 [ 2.185886@2] key_start=32 [ 2.188570@2] dtb_start=40 [ 2.191238@2] ddr_start=44 [ 2.193948@2] nbbt: info size=0x800 max_scan_blk=24, start_blk=20 [ 2.200442@2] get_free_node 43: bitmap=0 [ 2.203913@2] get_free_node 55: bitmap=1 [ 2.208004@2] get_free_node 43: bitmap=1 [ 2.211712@2] get_free_node 55: bitmap=3 [ 2.215804@2] get_free_node 43: bitmap=3 [ 2.219493@2] get_free_node 55: bitmap=7 [ 2.223395@2] nbbt : phy_blk_addr=20, ec=0, phy_page_addr=0, timestamp=1 [ 2.230082@2] nbbt free list: [ 2.233030@2] blockN=21, ec=-1, dirty_flag=0 [ 2.237276@2] blockN=22, ec=-1, dirty_flag=0 [ 2.241523@2] blockN=23, ec=-1, dirty_flag=0 [ 2.245770@2] aml_nand_scan_rsv_info 1141: page_num=1 [ 2.251182@2] nbbt valid addr: 280000 [ 2.254439@2] aml_nand_bbt_check 1306 bbt is valid, reading. [ 2.260081@2] aml_nand_read_rsv_info:423,read nbbt info at 280000 [ 2.266333@2] nenv: info size=0x10000 max_scan_blk=32, start_blk=24 [ 2.272762@2] get_free_node 43: bitmap=7 [ 2.276278@2] get_free_node 55: bitmap=f [ 2.280370@2] get_free_node 43: bitmap=f [ 2.284078@2] get_free_node 55: bitmap=1f [ 2.288257@2] get_free_node 43: bitmap=1f [ 2.292051@2] get_free_node 55: bitmap=3f [ 2.296230@2] get_free_node 43: bitmap=3f [ 2.300025@2] get_free_node 55: bitmap=7f [ 2.304203@2] get_free_node 43: bitmap=7f [ 2.307998@2] get_free_node 55: bitmap=ff [ 2.312177@2] get_free_node 43: bitmap=ff [ 2.315971@2] get_free_node 55: bitmap=1ff [ 2.320238@2] get_free_node 43: bitmap=1ff [ 2.324118@2] get_free_node 55: bitmap=3ff [ 2.328191@2] nenv : phy_blk_addr=24, ec=0, phy_page_addr=0, timestamp=1 [ 2.334862@2] nenv free list: [ 2.337809@2] blockN=25, ec=-1, dirty_flag=0 [ 2.342056@2] blockN=26, ec=-1, dirty_flag=0 [ 2.346302@2] blockN=27, ec=-1, dirty_flag=0 [ 2.350549@2] blockN=28, ec=-1, dirty_flag=0 [ 2.354796@2] blockN=29, ec=-1, dirty_flag=0 [ 2.359042@2] blockN=30, ec=-1, dirty_flag=0 [ 2.363289@2] blockN=31, ec=-1, dirty_flag=0 [ 2.367537@2] aml_nand_scan_rsv_info 1141: page_num=32 [ 2.384881@2] nenv valid addr: 310000 [ 2.384915@2] nkey: info size=0x8000 max_scan_blk=40, start_blk=32 [ 2.389274@2] get_free_node 43: bitmap=3ff [ 2.393157@2] get_free_node 55: bitmap=7ff [ 2.397422@2] get_free_node 43: bitmap=7ff [ 2.401303@2] get_free_node 55: bitmap=fff [ 2.405569@2] get_free_node 43: bitmap=fff [ 2.409450@2] get_free_node 55: bitmap=1fff [ 2.413801@2] get_free_node 43: bitmap=1fff [ 2.417770@2] get_free_node 55: bitmap=3fff [ 2.422123@2] get_free_node 43: bitmap=3fff [ 2.426090@2] get_free_node 55: bitmap=7fff [ 2.430443@2] get_free_node 43: bitmap=7fff [ 2.434409@2] get_free_node 55: bitmap=ffff [ 2.438762@2] get_free_node 43: bitmap=ffff [ 2.442730@2] get_free_node 55: bitmap=1ffff [ 2.447168@2] get_free_node 43: bitmap=1ffff [ 2.451223@2] get_free_node 55: bitmap=3ffff [ 2.455468@2] nkey : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0 [ 2.462141@2] nkey free list: [ 2.465088@2] blockN=32, ec=-1, dirty_flag=0 [ 2.469334@2] blockN=33, ec=-1, dirty_flag=0 [ 2.473581@2] blockN=34, ec=-1, dirty_flag=0 [ 2.477828@2] blockN=35, ec=-1, dirty_flag=0 [ 2.482074@2] blockN=36, ec=-1, dirty_flag=0 [ 2.486321@2] blockN=37, ec=-1, dirty_flag=0 [ 2.490567@2] blockN=38, ec=-1, dirty_flag=0 [ 2.494814@2] blockN=39, ec=-1, dirty_flag=0 [ 2.499061@2] aml_nand_scan_rsv_info 1141: page_num=16 [ 2.504174@2] nkey valid addr: fffffffffffe0000 [ 2.508681@2] aml_nand_key_check 1251 NO key exist [ 2.513449@2] ndtb: info size=0x20000 max_scan_blk=44, start_blk=40 [ 2.520107@2] get_free_node 43: bitmap=3ffff [ 2.523937@2] get_free_node 55: bitmap=7ffff [ 2.528376@2] get_free_node 43: bitmap=7ffff [ 2.532430@2] get_free_node 55: bitmap=fffff [ 2.536868@2] get_free_node 43: bitmap=fffff [ 2.540923@2] get_free_node 55: bitmap=1fffff [ 2.545256@2] ndtb : phy_blk_addr=40, ec=0, phy_page_addr=0, timestamp=1 [ 2.551927@2] ndtb free list: [ 2.554858@2] blockN=41, ec=-1, dirty_flag=0 [ 2.559121@2] blockN=42, ec=-1, dirty_flag=0 [ 2.563368@2] blockN=43, ec=-1, dirty_flag=0 [ 2.567615@2] aml_nand_scan_rsv_info 1141: page_num=64 [ 2.584915@2] ndtb valid addr: 500000 [ 2.584950@2] nddr: info size=0x20000 max_scan_blk=46, start_blk=44 [ 2.589398@2] get_free_node 43: bitmap=1fffff [ 2.593539@2] get_free_node 55: bitmap=3fffff [ 2.598065@2] get_free_node 43: bitmap=3fffff [ 2.602205@2] get_free_node 55: bitmap=7fffff [ 2.606538@2] nddr : phy_blk_addr=-1, ec=0, phy_page_addr=0, timestamp=0 [ 2.613209@2] nddr free list: [ 2.616156@2] blockN=44, ec=-1, dirty_flag=0 [ 2.620402@2] blockN=45, ec=-1, dirty_flag=0 [ 2.624650@2] aml_nand_scan_rsv_info 1141: page_num=64 [ 2.629763@2] nddr valid addr: fffffffffffe0000 [ 2.634270@2] aml_nand_ddr_check 1281 NO ddr exist [ 2.639040@2] tpl: off 8388608, size 8388608 [ 2.773315@2] Creating 6 MTD partitions on "nandnormal": [ 2.773362@2] 0x000000800000-0x000001000000 : "tpl" [ 2.784855@1] 0x000001000000-0x000001200000 : "misc" [ 2.788201@3] 0x000001200000-0x000002200000 : "recovery" [ 2.800415@1] 0x000002200000-0x000004200000 : "boot" [ 2.819972@1] 0x000004200000-0x000004700000 : "config" [ 2.824703@1] 0x000004700000-0x000010000000 : "nvdata" [ 2.927595@0] nandnormal initialized ok [ 2.927709@0] aml_ubootenv_init: register env chardev [ 2.931587@0] aml_ubootenv_init: register env chardev OK [ 2.936287@0] amlnf_dtb_init: register dtb cdev [ 2.941230@0] amlnf_dtb_init: register dtd cdev OK [ 2.945465@0] mtd_nand_probe 267 , err = 0 [ 2.950810@0] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc0 [ 2.956059@0] input: aml_vkeypad as /devices/platform/rtc/input/input0 [ 2.963208@0] unifykey: storage in base: 0xffffffc005000000 [ 2.967643@0] unifykey: storage out base: 0xffffffc005040000 [ 2.973235@0] unifykey: storage block base: 0xffffffc005080000 [ 2.979047@0] unifykey: probe done! [ 2.983241@0] unifykey: no efuse-version set, use default value: -1 [ 2.988775@0] unifykey: key unify config unifykey-num is 6 [ 2.994294@0] unifykey: key unify fact unifykey-num is 6 [ 2.999557@0] unifykey: unifykey_devno: f200000 [ 3.004518@2] unifykey: device unifykeys created ok [ 3.009003@2] unifykey: aml_unifykeys_init done! [ 3.013897@2] sysled: module init [ 3.017387@2] meson_wdt ffd0f0d0.watchdog: start watchdog [ 3.022143@2] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog [ 3.029577@1] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done [ 3.038288@3] dmc_monitor_probe [ 3.039133@3] page_trace_module_init, create sysfs failed [ 3.045009@3] defendkey defendkey: Reserved memory is not enough! [ 3.050254@3] defendkey: probe of defendkey failed with error -22 [ 3.056584@3] GACT probability NOT on [ 3.059935@3] Mirror/redirect action on [ 3.063727@3] u32 classifier [ 3.066554@3] Actions configured [ 3.070136@3] Netfilter messages via NETLINK v0.30. [ 3.075439@3] nf_conntrack version 0.5.0 (2048 buckets, 8192 max) [ 3.081624@3] ctnetlink v0.93: registering with nfnetlink. [ 3.087473@3] xt_time: kernel timezone is -0000 [ 3.091191@3] ipip: IPv4 and MPLS over IPv4 tunneling driver [ 3.097923@3] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.102546@3] arp_tables: arp_tables: (C) 2002 David S. Miller [ 3.108017@3] Initializing XFRM netlink socket [ 3.113583@3] NET: Registered protocol family 10 [ 3.119213@3] mip6: Mobile IPv6 [ 3.120123@3] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.126077@3] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.134087@3] NET: Registered protocol family 17 [ 3.136351@3] NET: Registered protocol family 15 [ 3.140923@3] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.154075@3] l2tp_core: L2TP core driver, V2.0 [ 3.158461@3] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 3.163388@3] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 3.169134@3] l2tp_netlink: L2TP netlink interface [ 3.173937@3] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 3.180002@3] l2tp_debugfs: L2TP debugfs support [ 3.184538@3] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 3.191187@3] NET: Registered protocol family 35 [ 3.196154@3] Key type dns_resolver registered [ 3.200671@3] Registered swp emulation handler [ 3.204576@3] Registered cp15_barrier emulation handler [ 3.209764@3] Registered setend emulation handler [ 3.214513@3] disable EAS feature [ 3.219308@1] registered taskstats version 1 [ 3.236376@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host [ 3.742850@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.742946@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 3.751248@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f664 hci version 0x100 quirks 0x02010010 [ 3.759672@3] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000 [ 3.767191@2] hub 1-0:1.0: USB hub found [ 3.769608@2] hub 1-0:1.0: 1 port detected [ 3.774253@2] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 3.779242@2] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 3.787147@2] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.796789@3] hub 2-0:1.0: USB hub found [ 3.799191@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 3.806531@3] usb usb2: Unsupported the hub [ 3.811339@3] aml_vrtc rtc: setting system clock to 2015-01-01 00:00:08 UTC (1420070408) [ 3.819345@3] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc00e15b000) [ 3.819421@3] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0 [ 3.827319@3] dwc_otg ff400000.dwc2_a: base=0xffffff8008580000 [ 3.827332@3] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc00c3f2a00 [ 3.927873@1] dwc_otg: Core Release: 3.10a [ 3.927930@1] dwc_otg: Setting default values for core params [ 3.932131@1] dwc_otg: curmode: 0, host_only: 0 [ 3.936632@1] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT [ 3.949164@1] dwc_otg: Using Buffer DMA mode [ 3.949202@1] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1 [ 3.953105@1] dwc_otg: Working on port type = SLAVE [ 3.957963@1] dwc_otg: Dedicated Tx FIFOs mode [ 3.965059@0] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22 [ 3.971724@0] cpucore_cooling_register, max_cpu_core_num:4 [ 3.984269@0] gxbb_pm: enter meson_pm_probe! [ 3.984327@0] no vddio3v3_en pin [ 3.985976@0] pm-meson aml_pm: Can't get switch_clk81 [ 3.991112@0] gxbb_pm: meson_pm_probe done [ 3.996038@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200 [ 4.002389@0] Freeing unused kernel memory: 3648K [ 4.016748@0] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200 [ 4.277915@1] ubi0: attaching mtd5 [ 4.296783@1] ubi0: scanning is finished [ 4.301441@3] ubi0: attached mtd5 (name "config", size 5 MiB) [ 4.301574@3] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.308638@3] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.315545@3] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.322653@3] ubi0: good PEBs: 40, bad PEBs: 0, corrupted PEBs: 0 [ 4.328711@3] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.336085@3] ubi0: max/mean erase counter: 13/6, WL threshold: 4096, image sequence number: 3362079202 [ 4.345491@3] ubi0: available PEBs: 0, total reserved PEBs: 40, PEBs reserved for bad PEB handling: 4 [ 4.354658@1] ubi0: background thread "ubi_bgt0d" started, PID 1075 [ 4.367777@0] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 1079 [ 4.384329@3] UBIFS (ubi0:0): recovery needed [ 4.420296@3] UBIFS (ubi0:0): recovery completed [ 4.420600@3] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "config_data" [ 4.427307@3] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.437344@3] UBIFS (ubi0:0): FS size: 2793472 bytes (2 MiB, 22 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 4.447565@3] UBIFS (ubi0:0): reserved for root: 131942 bytes (128 KiB) [ 4.454155@3] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID B381F50F-4ED2-44A4-BEBF-D138D5BC2291, small LPT model [ 4.478982@0] ubi2: attaching mtd6 [ 5.158930@0] ubi2: scanning is finished [ 5.166074@1] ubi2: attached mtd6 (name "nvdata", size 185 MiB) [ 5.166377@1] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 5.173490@1] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 5.180354@1] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 5.187447@1] ubi2: good PEBs: 1480, bad PEBs: 0, corrupted PEBs: 0 [ 5.193695@1] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 5.201055@1] ubi2: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 3917940917 [ 5.210335@1] ubi2: available PEBs: 0, total reserved PEBs: 1480, PEBs reserved for bad PEB handling: 4 [ 5.219716@0] ubi2: background thread "ubi_bgt2d" started, PID 1087 [ 5.232820@3] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 1091 [ 5.249437@1] UBIFS (ubi2:0): recovery needed [ 5.290289@2] UBIFS (ubi2:0): recovery completed [ 5.290600@2] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "nvdata_data" [ 5.297321@2] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 5.307339@2] UBIFS (ubi2:0): FS size: 185384960 bytes (176 MiB, 1460 LEBs), journal size 9269248 bytes (8 MiB, 73 LEBs) [ 5.318169@2] UBIFS (ubi2:0): reserved for root: 4952683 bytes (4836 KiB) [ 5.324930@2] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID BA7E6781-1356-4A44-A8AD-B533B5AD62E4, small LPT model [ 5.537611@0] eth0: device MAC address 02:b5:89:97:9c:ff [ 5.620528@3] meson6-dwmac ff3f0000.ethernet eth0: fail to init PTP. [ 5.621813@3] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.838223@0] uart_trans: loading out-of-tree module taints kernel. [ 5.840531@0] register uart_trans chrdev success. [ 5.844072@0] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 0 to 9600 [ 5.851640@0] tty port open success [/dev/ttyS3]! [ 5.856378@0] meson_uart ff804000.serial: ttyS3 use xtal(24M) 24000000 change 9600 to 115200 [ 5.864677@0] init sucess for tty struct (246:3) [/dev/ttyS3] [ 5.870831@0] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 0 to 9600 [ 5.878465@0] tty port open success [/dev/ttyS2]! [ 5.883134@0] meson_uart ffd23000.serial: ttyS2 use xtal(24M) 24000000 change 9600 to 115200 [ 5.891583@0] init sucess for tty struct (246:2) [/dev/ttyS2] [ 5.897662@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 0 to 9600 [ 5.905331@0] tty port open success [/dev/ttyS1]! [ 5.910003@0] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 9600 to 115200 [ 5.918408@0] init sucess for tty struct (246:1) [/dev/ttyS1] [ 5.924524@3] create workqueue success! [ 7.667839@3] meson6-dwmac ff3f0000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 7.671127@3] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 17.754948@0] uart trans dev open. [ 17.755057@0] uart_buf virt addr = 0xffffffc00bd40000 [ 17.757963@0] uart_buf phys addr = 0x0bd40000 [ 17.762159@0] uart_buf pfn = 0x0000bd40 [ 17.766859@0] uart trans stop send work timer. [ 17.771182@0] uart trans set chain exist bits:0x4. [ 17.775690@0] uart trans set work queue count 768. [ 30.404445@0] nf_conntrack: default automatic helper assignment has been turned off for security reasons and CT-based firewall rule not found. Use the iptables CT target to attach helpers instead. [ 76.512002@0] uart set baud to: 4098 [ 114.793984@0] uart trans stop send work timer. [ 115.113094@0] uart trans stop send work timer. [ 126.170689@3] uart trans start send work timer. ===========================================Miner log=========================================== 2015-01-01 00:00:15 Miner compile time: Tue Oct 19 21:30:41 CST 2021 type: Antminer S19j Pro 2015-01-01 00:00:16 This is fix-freq version 2015-01-01 00:00:16 Miner compile time: Tue Oct 19 21:30:41 CST 2021 type: Antminer S19j Pro 2015-01-01 00:00:16 commit version: ce69be1 2021-10-19 19:57:55, build by: jenkins 2021-10-19 21:46:16 2015-01-01 00:00:16 opt_multi_version = 1 2015-01-01 00:00:16 opt_bitmain_ab = 1 2015-01-01 00:00:16 mid_auto_gen = 1 2015-01-01 00:00:16 opt_bitmain_work_mode = 0 2015-01-01 00:00:16 port 439 already exported 2015-01-01 00:00:16 port 454 already exported 2015-01-01 00:00:16 no board pluged in socket 439 2015-01-01 00:00:16 port 440 already exported 2015-01-01 00:00:16 port 455 already exported 2015-01-01 00:00:16 no board pluged in socket 440 2015-01-01 00:00:16 port 441 already exported 2015-01-01 00:00:16 port 456 already exported 2015-01-01 00:00:16 port 438 already exported 2015-01-01 00:00:16 port 453 already exported 2015-01-01 00:00:16 port 446 already exported 2015-01-01 00:00:16 port 445 already exported 2015-01-01 00:00:16 Note: front fan is power on! 2015-01-01 00:00:16 Note: rear fan is power on! 2015-01-01 00:00:16 start the http log. 2015-01-01 00:00:16 httpListenThread start ret=0 2015-01-01 00:00:16 start listen on 6060 ... 2015-01-01 00:00:16 load machine BHB42601 conf 2015-01-01 00:00:16 machine : BHB42601 2015-01-01 00:00:16 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3 2015-01-01 00:00:16 bad chain id = 3 2015-01-01 00:00:19 bad chain id = 3 2015-01-01 00:00:21 ==========================capability start========================== 2015-01-01 00:00:21 board num = 1 2015-01-01 00:00:21 board id = 2, chain num = 1 2015-01-01 00:00:21 chain id = 2 2015-01-01 00:00:21 ==========================capability end============================ 2015-01-01 00:00:21 chain num = 1 2015-01-01 00:00:22 load chain 2 eeprom data 2015-01-01 00:00:22 fan_eft : 0 fan_pwm : 100 2015-01-01 00:00:22 create thread get_nonce_and_register_thread 2015-01-01 00:00:22 fixed working voltage = 1360 2015-01-01 00:00:22 Chain [2] PCB Version: 0x0130 2015-01-01 00:00:22 Chain [2] BOM Version: 0x0010 2015-01-01 00:00:22 bad chain id = 3 2015-01-01 00:00:22 Fan check passed. 2015-01-01 00:00:22 uart_trans addr:0xf6e43000. 2015-01-01 00:00:23 chain[2] PIC jump to app 2015-01-01 00:00:24 Check chain[2] PIC fw version=0x89 2015-01-01 00:00:24 create thread pic_heart_beat_thread 2015-01-01 00:00:24 max sensor num = 4 2015-01-01 00:00:24 STATUS_INITED: soc init done! 2015-01-01 00:00:24 temperature_monitor_thread start... 2022-08-10 13:24:17 start to init... 2022-08-10 13:24:17 i2c_sim_init start 2022-08-10 13:24:17 init gpio477 2022-08-10 13:24:17 init gpio476 2022-08-10 13:24:18 i2c_sim_init end 2022-08-10 13:24:19 power open power_version = 0x71 2022-08-10 13:24:20 power type version: 0x0071 2022-08-10 13:24:20 Enter sleep to make sure power release finish. 2022-08-10 13:24:51 Slept 30 seconds, diff = 1. 2022-08-10 13:24:52 set_voltage_by_steps to 1500. 2022-08-10 13:24:54 chain avg vol rise to 15.38 2022-08-10 13:24:56 start up min temp by 75a = 26 2022-08-10 13:25:02 chain avg vol drop to 0.78 2022-08-10 13:25:06 Chain[2]: find 0 asic, times 0 2022-08-10 13:25:09 chain avg vol rise to 15.36 2022-08-10 13:25:13 chain avg vol drop to 0.86 2022-08-10 13:25:17 Chain[2]: find 0 asic, times 1 2022-08-10 13:25:18 chain avg vol rise to 14.62 2022-08-10 13:25:18 chain avg vol drop to 0.73 2022-08-10 13:25:21 chain avg vol rise to 15.36 2022-08-10 13:25:25 chain avg vol drop to 0.86 2022-08-10 13:25:29 Chain[2]: find 0 asic, times 2 2022-08-10 13:25:30 chain avg vol rise to 14.77 2022-08-10 13:25:30 chain avg vol drop to 0.71 2022-08-10 13:25:31 Chain 2 only find 0 asic, will power off hash board 2 2022-08-10 13:25:31 ERROR_SOC_INIT: soc init failed! 2022-08-10 13:25:31 stop_mining: soc init failed! 2022-08-10 13:25:31 uninit_temp_info 2022-08-10 13:25:31 do not read temp anymore... 2022-08-10 13:25:31 cancel thread 2022-08-10 13:25:31 cancel thread 2022-08-10 13:25:31 ****power off hashboard**** 2022-08-10 13:25:31 over max temp, pcb temp 255 (max 75), chip temp 255(max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 0 2022-08-10 13:25:31 Sweep error string = P:1. 2022-08-10 13:25:31 ERROR_TEMP_TOO_HIGH: over max temp 2022-08-10 13:25:31 stop_mining: over max temp 2022-08-10 13:25:31 ****power off hashboard**** 2022-08-10 13:25:35 temp monitor thread exit 2022-08-10 13:25:46 Version num 65536 2022-08-10 13:25:46 Mask num 0x1fffe000 2022-08-10 13:25:46 Note: addrInterval or corenum is not initialized. [/spoiler] не тот лог приложил, правильный ло ===========================================Miner log=========================================== 2015-01-01 00:00:15 Miner compile time: Tue Oct 19 21:30:41 CST 2021 type: Antminer S19j Pro 2015-01-01 00:00:16 This is fix-freq version 2015-01-01 00:00:16 Miner compile time: Tue Oct 19 21:30:41 CST 2021 type: Antminer S19j Pro 2015-01-01 00:00:16 commit version: ce69be1 2021-10-19 19:57:55, build by: jenkins 2021-10-19 21:46:16 2015-01-01 00:00:16 opt_multi_version = 1 2015-01-01 00:00:16 opt_bitmain_ab = 1 2015-01-01 00:00:16 mid_auto_gen = 1 2015-01-01 00:00:16 opt_bitmain_work_mode = 0 2015-01-01 00:00:16 port 439 already exported 2015-01-01 00:00:16 port 454 already exported 2015-01-01 00:00:16 port 440 already exported 2015-01-01 00:00:16 port 455 already exported 2015-01-01 00:00:16 port 441 already exported 2015-01-01 00:00:16 port 456 already exported 2015-01-01 00:00:16 port 438 already exported 2015-01-01 00:00:16 port 453 already exported 2015-01-01 00:00:16 port 446 already exported 2015-01-01 00:00:16 port 445 already exported 2015-01-01 00:00:16 Note: front fan is power on! 2015-01-01 00:00:16 Note: rear fan is power on! 2015-01-01 00:00:16 start the http log. 2015-01-01 00:00:16 httpListenThread start ret=0 2015-01-01 00:00:16 start listen on 6060 ... 2015-01-01 00:00:16 load machine BHB42601 conf 2015-01-01 00:00:16 machine : BHB42601 2015-01-01 00:00:16 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3 2015-01-01 00:00:16 bad chain id = 3 2015-01-01 00:00:19 bad chain id = 3 2015-01-01 00:00:21 ==========================capability start========================== 2015-01-01 00:00:21 board num = 3 2015-01-01 00:00:21 board id = 0, chain num = 1 2015-01-01 00:00:21 chain id = 0 2015-01-01 00:00:21 board id = 1, chain num = 1 2015-01-01 00:00:21 chain id = 1 2015-01-01 00:00:21 board id = 2, chain num = 1 2015-01-01 00:00:21 chain id = 2 2015-01-01 00:00:21 ==========================capability end============================ 2015-01-01 00:00:21 chain num = 3 2015-01-01 00:00:22 load chain 0 eeprom data 2015-01-01 00:00:23 load chain 1 eeprom data 2015-01-01 00:00:23 load chain 2 eeprom data 2015-01-01 00:00:23 fan_eft : 0 fan_pwm : 100 2015-01-01 00:00:23 create thread get_nonce_and_register_thread 2015-01-01 00:00:23 fixed working voltage = 1360 2015-01-01 00:00:23 Chain [0] PCB Version: 0x0130 2015-01-01 00:00:23 Chain [0] BOM Version: 0x0010 2015-01-01 00:00:23 Chain [1] PCB Version: 0x0130 2015-01-01 00:00:23 Chain [1] BOM Version: 0x0010 2015-01-01 00:00:23 Chain [2] PCB Version: 0x0130 2015-01-01 00:00:23 Chain [2] BOM Version: 0x0010 2015-01-01 00:00:23 bad chain id = 3 2015-01-01 00:00:23 Fan check passed. 2015-01-01 00:00:23 uart_trans addr:0xf747e000. 2022-08-10 13:40:48 chain[0] PIC jump to app 2022-08-10 13:40:49 Check chain[0] PIC fw version=0x89 2022-08-10 13:40:50 chain[1] PIC jump to app 2022-08-10 13:40:52 Check chain[1] PIC fw version=0x89 2022-08-10 13:40:53 chain[2] PIC jump to app 2022-08-10 13:40:54 Check chain[2] PIC fw version=0x89 2022-08-10 13:40:54 create thread pic_heart_beat_thread 2022-08-10 13:40:54 max sensor num = 4 2022-08-10 13:40:54 STATUS_INITED: soc init done! 2022-08-10 13:40:54 temperature_monitor_thread start... 2022-08-10 13:41:07 start to init... 2022-08-10 13:41:07 i2c_sim_init start 2022-08-10 13:41:07 init gpio477 2022-08-10 13:41:07 init gpio476 2022-08-10 13:41:07 i2c_sim_init end 2022-08-10 13:41:08 power open power_version = 0x71 2022-08-10 13:41:10 power type version: 0x0071 2022-08-10 13:41:10 Enter sleep to make sure power release finish. 2022-08-10 13:41:12 chain avg vol drop to 9.21 2022-08-10 13:41:41 Slept 30 seconds, diff = 1. 2022-08-10 13:41:42 set_voltage_by_steps to 1500. 2022-08-10 13:41:45 chain avg vol rise to 10.42 2022-08-10 13:41:46 chain avg vol rise to 15.34 2022-08-10 13:41:47 start up min temp by 75a = 27 2022-08-10 13:41:54 chain avg vol drop to 5.54 2022-08-10 13:41:57 Chain[0]: find 0 asic, times 0 2022-08-10 13:42:01 chain avg vol rise to 10.41 2022-08-10 13:42:02 chain avg vol rise to 15.35 2022-08-10 13:42:05 chain avg vol drop to 10.47 2022-08-10 13:42:06 chain avg vol drop to 0.56 2022-08-10 13:42:09 Chain[0]: find 0 asic, times 1 2022-08-10 13:42:13 chain avg vol rise to 15.34 2022-08-10 13:42:17 chain avg vol drop to 5.54 2022-08-10 13:42:21 Chain[0]: find 0 asic, times 2 2022-08-10 13:42:23 Chain 0 only find 0 asic, will power off hash board 0 2022-08-10 13:42:25 chain avg vol rise to 15.33 2022-08-10 13:42:30 chain avg vol drop to 0.56 2022-08-10 13:42:33 Chain[1]: find 0 asic, times 0 2022-08-10 13:42:37 chain avg vol rise to 15.33 2022-08-10 13:42:41 chain avg vol drop to 8.02 2022-08-10 13:42:45 Chain[1]: find 0 asic, times 1 2022-08-10 13:42:49 chain avg vol rise to 15.33 2022-08-10 13:42:53 chain avg vol drop to 8.06 2022-08-10 13:42:57 Chain[1]: find 0 asic, times 2 2022-08-10 13:42:59 Chain 1 only find 0 asic, will power off hash board 1 2022-08-10 13:43:00 chain avg vol rise to 15.36 2022-08-10 13:43:05 chain avg vol drop to 0.83 2022-08-10 13:43:09 Chain[2]: find 0 asic, times 0 2022-08-10 13:43:09 chain avg vol rise to 15.23 2022-08-10 13:43:10 chain avg vol drop to 0.64 2022-08-10 13:43:12 chain avg vol rise to 15.38 2022-08-10 13:43:17 chain avg vol drop to 0.78 2022-08-10 13:43:21 Chain[2]: find 0 asic, times 1 2022-08-10 13:43:24 chain avg vol rise to 15.36 2022-08-10 13:43:29 chain avg vol drop to 0.78 2022-08-10 13:43:33 Chain[2]: find 0 asic, times 2 2022-08-10 13:43:33 chain avg vol rise to 15.23 2022-08-10 13:43:34 chain avg vol drop to 0.54 2022-08-10 13:43:35 Chain 2 only find 0 asic, will power off hash board 2 2022-08-10 13:43:35 ERROR_SOC_INIT: soc init failed! 2022-08-10 13:43:35 stop_mining: soc init failed! 2022-08-10 13:43:35 uninit_temp_info 2022-08-10 13:43:35 do not read temp anymore... 2022-08-10 13:43:35 cancel thread 2022-08-10 13:43:35 cancel thread 2022-08-10 13:43:35 ****power off hashboard**** 2022-08-10 13:43:35 over max temp, pcb temp 255 (max 75), chip temp 255(max 95) pcb temp rise 0 chip temp rise 0, total_exit_failure 0 2022-08-10 13:43:35 Sweep error string = P:1. 2022-08-10 13:43:35 ERROR_TEMP_TOO_HIGH: over max temp 2022-08-10 13:43:35 stop_mining: over max temp 2022-08-10 13:43:35 ****power off hashboard**** 2022-08-10 13:43:38 temp monitor thread exit Ссылка на комментарий Поделиться на других сайтах Прочее
Вадим Gredorn Опубликовано 16 Ноября 2022 Поделиться Опубликовано 16 Ноября 2022 Приветствую, возможно я ошибаюсь, но судя по логу есть конфликт с датчиками температуры, возможно стоит их заменить, так же по какой-то причине дропается питания хеш плат, это может быть БП или где-то кз на хеш плате ( попробуйте замерить сопротивления на ЛДО) Ссылка на комментарий Поделиться на других сайтах Прочее
Serg Bitriver Tsyvkin Опубликовано 24 Ноября 2022 Поделиться Опубликовано 24 Ноября 2022 Проблема в БП. Температурные датчики не виноваты. 1 Ссылка на комментарий Поделиться на других сайтах Прочее
032 Опубликовано 28 Апреля 2023 Поделиться Опубликовано 28 Апреля 2023 Вы издеваетесь ? Кто кидает логи таким образом - глаза, ну сделайте вы текстовый документ и туда всё это г с телефона сиди час листай в низ 👇 Ссылка на комментарий Поделиться на других сайтах Прочее
Рекомендуемые сообщения
Пожалуйста, авторизуйтесь, чтобы оставить комментарий
Вы сможете оставлять комментарии после авторизации
Войти